Original 300/500W Laser Die Cutter's Co2 Power Supplies

  • Original 300/500W Laser Die Cutter's Co2 Power Supplies
  • Original 300/500W Laser Die Cutter's Co2 Power Supplies
Original 300/500W Laser Die Cutter's Co2 Power Supplies
  • ZRsuns
  • Linyi China
  • 1-2 working days
  • 30000PCS each month

1.The laser die cutter's co2 power supplies’ control is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
2 This300/500watt co2 power supplies are equipped with two cooling fans on each power supply. Better heat dissipation can protect the internal electronic components of the 300/500watt co2 power supplies
3. Input analog signal(0~5V) or PWM is used to control the output laser power on this original co2 power supplies.

ZR-300WA CO2 laser power supply 

Feature

1.The laser die cutter's co2 power supplies' control is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.

2 This 300/500watt co2 power supplies are equipped with two cooling fans on each power supply. Better heat dissipation can protect the internal electronic components of the 300/500watt co2 power supplies

original co2 power supplies

3. Input analog signal(0~5V) or PWM is used to control the output laser power on this original co2 power supplies.

4..The laser die cutter's co2 power supplies have H/L/P/G/IN/5V control signal port,The upper cover and bottom shell are aluminum shell is galvanized sheet.

300/500watt co2 power supplies

5.Each 300/500watt co2 power supplies before selling will go through the aging check:

(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;

(2) 500 times on/off check for 7 seconds.

6.The original co2 power supplies are well grounded, which can ensure the safety of operators. At the same time, the original co2 power supplies also have an open circuit protection function, which allows the original co2 power supplies on laser cutter to work for a short time in the open circuit state.

laser die cutter's co2 power supplies

7.The laser die cutter's co2 power supplies can match with EFR,Yongli,SPT, Weiju and other factories’ 500 or 300watt sealed glass type CO2 laser tube.  If it is a 300W laser tube, two 150W laser power supplies will be used in parallel. If it is a 500W laser tube, three 150W laser power supplies will be used in parallel.

8.The laser die cutter's co2 power supplies use zero-current half-bridge soft-switch circuit to make sure the laser die cutter's co2 power supplies have high efficiency and fast response speed.

9.The 300/500watt co2 power supplies have RED TEST button to easily figure out CO2 power supplies or CO2 laser tube’s failure. It is very easy and simple to remove trouble.

original co2 power supplies


Specification

Input

Input voltage

AC220V±10% (AC110V specified while order)


AC frequency

47~440HZ


Maximum input power

3300W


Maximum input current

5A

Output

Maximum output voltage

50KV


Maximum output current

38mAx3

(depending on the laser tubes of different manufacturers)

Efficiency

More than 90% (Full load)

Response speed

Not more than 1ms

Control lnterace

TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)

Insulation

lnput-output

AC 1500V 1 minutes not more than 10mA


lnput-shell

AC 1500V 1 minutes not more than10mA


Output-shell

Connection

Open Circuit Protection

Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)

Environmental Requested

Working temperature

-10℃~50℃


Storage of temperature

-20℃~75℃


Relative Humidity

Maximum 85%RH (non-condensing)


Altitude

100,000 feet of work

200,000 feet of storage,dose not work

Cooling methods

Forced air cooling (fan cooling)

Dimensions (LxWxH)

350mmx222mmx105mmx3


300/500watt co2 power supplies

Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy

close left right